ATV61HC40N4 - variable speed drive ATV61 - 400kW 600HP - 380...480V - IP20

ATV61HC40N4

variable speed drive ATV61 - 400kW 600HP - 380...480V - IP20

Add to Quote Catalogue

Specifications

Line Current	597 A 480 V 3 phase 355 kW 637 A 380 V 3 phase 355 kW 644 A 480 V 3 phase 400 kW / 600 hp 709 A 380 V 3 phase 400 kW / 600 hp
Range Of Product	Altivar 61
Asynchronous Motor Control Profile	voltage/frequency ratio - Energy Saving, quadratic U/f voltage/frequency ratio, 2 points voltage/frequency ratio, 5 points flux vector control without sensor, standard
Product Or Component Type	variable speed drive
Apparent Power	419.3 kVA 380 V 3 phase 355 kW 466.6 kVA 380 V 3 phase 400 kW / 600 hp
Component Name	ATV61
Motor Power Kw	355 kW, 3 phase 380...480 V 400 kW, 3 phase 380...480 V
Phase	3 phase
Switching Frequency	2...8 kHz adjustable 2.5...8 kHz with derating factor
Maximum Transient Current	910.8 A 60 s, 3 phase
[Us] Rated Supply Voltage	380...480 V - 15...10 %
Communication Port Protocol	Modbus CANopen
Product Specific Application	pumping and ventilation machine
Assembly Style	with heat sink
Nominal Switching Frequency	2.5 kHz
Emc Filter	Level 3 EMC filter
Type Of Polarization	no impedance Modbus
Maximum Horse Power Rating	600 hp, 3 phase 380...480 V
Prospective Line Isc	50 kA 3 phase
Synchronous Motor Control Profile	vector control without sensor, standard
Option Card	communication card APOGEE FLN communication card LonWorks communication card METASYS N2 communication card Modbus Plus communication card Modbus TCP communication card Modbus/Uni-Telway multi-pump card communication card Profibus DP communication card Profibus DP V1 communication card BACnet communication card CC-Link controller inside programmable card communication card DeviceNet communication card EtherNet/IP communication card Fipio I/O extension card communication card Interbus-S
Warranty	18 months
Network Frequency	47.5...63 Hz
Discrete Input Logic	negative logic (sink) LI1...LI5), > 16 V, < 10 V positive logic (source) LI1...LI5), < 5 V, > 11 V negative logic (sink) LI6)if configured as logic input, > 16 V, < 10 V positive logic (source) LI6)if configured as logic input, < 5 V, > 11 V
Product Destination	synchronous motors asynchronous motors
Type Of Cable	with an IP21 or an IP31 kit 3 IEC cable 40 °C, copper 70 °C / PVC with UL Type 1 kit 3 UL 508 cable 40 °C, copper 75 °C / PVC without mounting kit 1 IEC cable 45 °C, copper 70 °C / PVC without mounting kit 1 IEC cable 45 °C, copper 90 °C / XLPE/EPR
Height	1390 mm
Acceleration And Deceleration Ramps	linear adjustable separately from 0.01 to 9000 s automatic adaptation of ramp if braking capacity exceeded, by using resistor S, U or customized
Physical Interface	2-wire RS 485 Modbus
Discrete Output Type	configurable relay logic R1A, R1B, R1C) NO/NC - 100000 cycles configurable relay logic R2A, R2B) NO - 100000 cycles
Maximum Switching Current	R1, R2 2 A 250 V AC inductive, cos phi = 0.4 7 ms R1, R2 2 A 30 V DC inductive, cos phi = 0.4 7 ms R1, R2 5 A 250 V AC resistive, cos phi = 1 0 ms R1, R2 5 A 30 V DC resistive, cos phi = 1 0 ms
Torque Accuracy	+/- 15 % in open-loop mode, without speed feedback
Transient Overtorque	130-130 % of nominal motor torque +/- 10 % 60 s
Output Frequency	0.1-500 Hz
Data Format	8 bits, 1 stop, even parity Modbus on front face 8 bits, odd even or no configurable parity Modbus on terminal
Insulation Resistance	> 1 mOhm 500 V DC for 1 minute to earth
Response Time	<= 100 ms in STO (Safe Torque Off) R1A, R1B, R1C <= 7 ms +/- 0.5 ms R2A, R2B <= 7 ms +/- 0.5 ms
Marking	CE
Net Weight	320 kg
Frequency Resolution	analog input 0.024/50 Hz display unit 0.1 Hz
Accuracy	+/- 0.6 % AI1-/Al1+) for a temperature variation 60 °C +/- 0.6 % AI2) for a temperature variation 60 °C +/- 1 % AO1) for a temperature variation 60 °C
Connector Type	1 RJ45 on front face)Modbus 1 RJ45 on terminal)Modbus male SUB-D 9 on RJ45CANopen
Electrical Connection	terminal 2.5 mm² / AWG 14 AI1-/AI1+, AI2, AO1, R1A, R1B, R1C, R2A, R2B, LI1...LI6, PWR) terminal 4 x 185 mm² / 4 x 500 kcmil L1/R, L2/S, L3/T, U/T1, V/T2, W/T3) terminal 8 x 185 mm² / 4 x 500 kcmil PC/-, PO, PA/+)
Analogue Input Number	2
Motor Slip Compensation	can be suppressed automatic whatever the load not available in voltage/frequency ratio (2 or 5 points) adjustable
Discrete Output Number	2
Transmission Frame	RTU Modbus
Regulation Loop	frequency PI regulator
Supply Voltage Limits	323-528 V
Minimum Switching Current	3 mA 24 V DC configurable relay logic
Discrete Input Type	programmable LI1...LI5) 24 V DC <= 30 V)level 1 PLC - 3500 Ohm switch-configurable LI6) 24 V DC <= 30 V)level 1 PLC - 3500 Ohm switch-configurable PTC probe LI6)0-6 - 1500 Ohm safety input PWR) 24 V DC <= 30 V) - 1500 Ohm
Analogue Output Number	1
Transmission Rate	4800 bps, 9600 bps, 19200 bps, 38.4 Kbps Modbus on terminal 9600 bps, 19200 bps Modbus on front face 20 kbps, 50 kbps, 125 kbps, 250 kbps, 500 kbps, 1 Mbps CANopen
Method Of Access	slave CANopen
Continuous Output Current	759 A 2.5 kHz, 380 V - 3 phase 759 A 2.5 kHz, 460 V - 3 phase
Tightening Torque	0.6 N.m AI1-/AI1+, AI2, AO1, R1A, R1B, R1C, R2A, R2B, LI1...LI6, PWR) 41 N.m, 360 lb.in PC/-, PO, PA/+) 41 N.m, 360 lb.in L1/R, L2/S, L3/T, U/T1, V/T2, W/T3)
Speed Range	1-100 in open-loop mode, without speed feedback
Isolation	between power and control terminals
Discrete Input Number	7
Local Signalling	for drive voltage 1 LED (red)
Linearity Error	+/- 0.15 % of maximum value AI1-/Al1+) +/- 0.15 % of maximum value AI2) +/- 0.2 % AO1)
Number Of Addresses	1-127 CANopen 1-247 Modbus
Output Voltage	<= power supply voltage
Operating Position	vertical +/- 10 degree
Width	890 mm
Braking To Standstill	by DC injection
Depth	377 mm
Analogue Output Type	AO1 software-configurable current 0...20 mA 500 Ohm 10 bits AO1 software-configurable voltage 0...10 V DC 470 Ohm 10 bits AO1 software-configurable logic output 10 V, 20-20 mA
Protection Type	against exceeding limit speed drive power removal drive short-circuit between motor phases drive thermal protection drive motor phase break motor power removal motor thermal protection motor against input phase loss drive break on the control circuit drive input phase breaks drive line supply overvoltage drive line supply undervoltage drive overcurrent between output phases and earth drive overheating protection drive overvoltages on the DC bus drive
Supply	internal supply for reference potentiometer (1 to 10 kOhm) 10.5 V DC, +/- 5 %, <10 mA overload and short-circuit protection internal supply 24 V DC 21-27 V), <200 mA overload and short-circuit protection external supply 24 V DC 19-30 V)
Analogue Input Type	AI1-/Al1+ bipolar differential voltage +/- 10 V DC 24 V max 11 bits + sign AI2 software-configurable current 0...20 mA 242 Ohm 11 bits AI2 software-configurable voltage 0...10 V DC 24 V max 30000 Ohm 11 bits
Braking Torque	<= 125 % with braking resistor 30 % without braking resistor
Supply Frequency	50...60 Hz - 5...5 %
Sampling Duration	2 ms +/- 0.5 ms AI1-/Al1+) - analog input 2 ms +/- 0.5 ms Al2) - analog input 2 ms +/- 0.5 ms AO1) - analog output 2 ms +/- 0.5 ms LI1...LI5) - discrete input 2 ms +/- 0.5 ms LI6)if configured as logic input - discrete input
Speed Accuracy	+/- 10 % of nominal slip 0.2 Tn to Tn without speed feedback
Rohs Exemption Information	Yes
Mercury Free	Yes
Environmental Disclosure	ENVPEP091204EN
Sustainable Offer Status	Green Premium product
California Proposition 65	WARNING: This product can expose you to chemicals including: Lead and lead compounds, which is known to the State of California to cause cancer and birth defects or other reproductive harm. For more information go to www.P65Warnings.ca.gov
Weee	The product must be disposed on European Union markets following specific waste collection and never end up in rubbish bins.
China Rohs Regulation	X
Eu Rohs Directive	Pro-active compliance (Product out of EU RoHS legal scope)
Product Certifications	CSA DNV UL C-tick NOM 117 GOST
Standards	EN 61800-3 environments 2 category C3 EN 55011 class A group 2 EN 61800-3 environments 1 category C3 IEC 60721-3-3 class 3C2 EN/IEC 61800-3 UL Type 1 EN/IEC 61800-5-1
Electromagnetic Compatibility	conducted radio-frequency immunity test level 3 IEC 61000-4-6 electrical fast transient/burst immunity test level 4 IEC 61000-4-4 electrostatic discharge immunity test level 3 IEC 61000-4-2 radiated radio-frequency electromagnetic field immunity test level 3 IEC 61000-4-3 voltage dips and interruptions immunity test IEC 61000-4-11
Ambient Air Temperature For Operation	-10-45 °C without derating) 45-60 °C with derating factor)
Shock Resistance	4 gn 11 ms EN/IEC 60068-2-27
Dielectric Strength	3535 V DC between earth and power terminals 5092 V DC between control and power terminals
Vibration Resistance	0.6 gn 10-200 Hz)EN/IEC 60068-2-6 1.5 mm peak to peak 3-10 Hz)EN/IEC 60068-2-6
Noise Level	70 dB 86/188/EEC
Pollution Degree	3 EN/IEC 61800-5-1 3 UL 840
Ambient Air Temperature For Storage	-25-70 °C
Relative Humidity	5-95 % without condensation IEC 60068-2-3 5-95 % without dripping water IEC 60068-2-3
Ip Degree Of Protection	IP41 on upper part EN/IEC 60529 IP41 on upper part EN/IEC 61800-5-1 IP00 EN/IEC 60529 IP00 EN/IEC 61800-5-1 IP30 on side parts EN/IEC 60529 IP30 on side parts EN/IEC 61800-5-1 IP30 on the front panel EN/IEC 60529 IP30 on the front panel EN/IEC 61800-5-1
Operating Altitude	<= 3280.84 ft (1000 m) without derating 3280.84...9842.52 ft (1000...3000 m) with current derating 1 % per 100 m

variable speed drive ATV61 - 400kW 600HP - 380...480V - IP20

Specifications

Documents

Royal Wholesale Electric