| Range Of Product |
Lexium 28 |
| Product Or Component Type |
Motion servo drive |
| Device Short Name |
LXM28A |
| Format Of The Drive |
Compact housing |
| Line Current |
2.4 A 226.8 % 220 V, single phase
2.4 A 200.7 % 220 V, three phase |
| Network Number Of Phases |
Three phase
Single phase |
| [Us] Rated Supply Voltage |
220 V - 10...15 %)three phase
220 V - 20...15 %)single phase |
| Supply Voltage Limits |
200…255 V three phase
170…255 V single phase |
| Supply Frequency |
50/60 Hz - 5...5 % |
| Network Frequency |
47.5...63 Hz |
| Emc Filter |
Without EMC filter |
| Continuous Output Current |
1.5 A 16 kHz |
| Output Current 3S Peak |
4.5 A 220 V |
| Continuous Power |
200 W 220 V |
| Nominal Power |
0.2 kW 220 V 16 kHz |
| Switching Frequency |
16 kHz |
| Overvoltage Category |
III |
| Leakage Current |
1.3 mA |
| Output Voltage |
<= power supply voltage |
| Electrical ISOlation |
Between power and control |
| Type Of Cable |
Shielded motor cable 32…131 °F (0…55 °C)) copper |
| Electrical Connection |
Spring terminal 0.82...1 mm², AWG 18 L1-L2)
Spring terminal 0.82...1 mm², AWG 18 R, S, T)
Spring terminal 0.82...1 mm², AWG 18 U, V, W, PE)
Spring terminal 0.82...1 mm², AWG 18 PA/+, PBe) |
| Discrete Input Number |
8 programmable CN1)
1 pulse train input (PTI) CN1)
2 fast capture CN1)
1 safety function STO CN9) |
| Discrete Input Voltage |
24 V DC logic |
| Discrete Input Logic |
Positive or negative CN1) |
| Discrete Output Number |
5 logic output CN1)12...24 V DC
1 pulse train output (PTO) CN1) |
| Discrete Output Voltage |
12...24 V DC |
| Discrete Output Logic |
Positive or negative CN1) |
| Analogue Input Number |
2 |
| Absolute Accuracy Error |
0.1 % |
| Analogue Input Type |
V_REF voltage analog input - 10...10 V 10 kOhm 14 bits
T_REF voltage analog input |
| Control Signal Type |
Servo motor encoder feedback CN2 |
| Protection Type |
Against reverse polarity inputs signal
Against short-circuits outputs signal
Overcurrent motor
Overvoltage motor
Undervoltage motor
Overheating motor
Overload motor
Overspeed motor |
| Safety Function |
STO (safe torque off), Integrated |
| Safety Level |
SIL 2 IEC 61800-5-2 2007
SIL 2 IEC 61508-1 2010
PL d/category 3 EN/ISO 13849-1 2008
SIL 2 EN/ISO 13849-1 2009/AC
SIL 2 EN 60204-1 2006
SIL 2 EN 60204-1 2009/A1
SIL 2 EN 60204-1 2010/AC
SIL 2 IEC 62061 2012 |
| Communication Interface |
CANopen, Integrated
CANmotion, Integrated |
| Connector Type |
RJ45 CN4)CANopen, CANmotion |
| Method Of Access |
Slave |
| Transmission Rate |
250 kbit/s 328.08…820.21 ft (100…250 m) CANopen, CANmotion
500 kbit/s 13.12…328.08 ft (4…100 m) CANopen, CANmotion
1 Mbit/s 13.12 ft (4 m) CANopen, CANmotion |
| Number Of Addresses |
1…127 CANopen, CANmotion |
| Physical Interface |
RS485 Modbus Serial line slave |
| Status Led |
Charge 1 LED Red)
RUN 1 LED Green)
Error 1 LED Red) |
| Signalling Function |
Servo status and fault codes five 7-segment display units |
| Marking |
CSA
CULus
CE |
| Type Of Cooling |
Natural convection |
| Operating Position |
Vertical |
| Product Compatibility |
Servo motor BCH2 2.36 in (60 mm), 1 200 W |
| Width |
2.17 in (55 mm) |
| Height |
5.91 in (150 mm) |
| Depth |
5.75 in (146 mm) |
